Electric wrench is an electric tool for tightening and loosening bolts and nuts. It is a tool for fastening high strength bolts. It is used for the initial twist, final twist and initial twist of shear type high strength bolts for installation of large hexagonal head high strength bolts in steel structure bridges, factory buildings, chemical industry and power generation equipment, as well as the occasions where the torque or axial force of bolt fasteners is strictly required. The following is a small twist scissors wrench knitting to introduce the use of electric wrenches caution!

　　電動扳手11點注意事項，做好了，施工容易完成!

 

　　Electric wrench 11 points of attention, done, construction easy to complete!

　　預防措施的使用

　　Use of preventive measures

　　1)工具通電前，插入前應檢查開關是否處于斷開狀態。

　　1) Before the tool is energized, the switch should be checked to see if it is disconnected before insertion.

　　2)確認現場連接的電源是否與電動扳手所需電壓一致，是否有漏電保護器連接。

　　2) Verify whether the power supply connected on site is in accordance with the voltage required by the electric wrench and whether there is a leakage protector connection.

　　3)根據螺母的尺寸選擇配套的套筒，并正確安裝。

　　3) Select the matching sleeve according to the size of the nut and install it correctly.

　　4)高電壓或低電壓不適合使用。

　　4) High or low voltage is not suitable for use.

　　5)不要使用簡化形式作為錘子工具。

　　5) Do not use simplified forms as hammer tools.

　　扭剪扳手

　　Torsion wrench

　　6)不要在搖臂桿上增加套筒桿或撬桿來增加力。

　　6) Do not add sleeve rod or pry rod to rocker rod to increase force.

　　7)電動扳手金屬外殼需要可靠接地。

　　7) Electric wrench metal shell needs reliable grounding.

　　8)檢查電動扳手本體安裝螺絲的緊固性。如果發現螺釘松動，應立即重新擰緊。

　　8) Check the tightness of the installation screw of the electric wrench body. If the screw is loose, it should be tightened again immediately.

　　9)檢查手持式電動扳手兩側把手是否完好，安裝是否牢固。

　　9) Check whether the handles on both sides of the hand-held electric wrench are in good condition and the installation is firm.

　　10)應采取措施防止在梯子上工作或在高處工作時跌倒。

　　10) Measures should be taken to prevent falls while working on ladders or at high altitudes.

　　11)如果工作現場距離電源較遠，需要對電纜進行延伸時，應使用容量足夠且安裝合格的延伸電纜。

　　11) If the work site is far away from the power supply, the cable should be extended with sufficient capacity and qualified extension cable installed.

　　以上是扭剪扳手11點注意事項，對干貨進行總結，提出建議。訪問網站http://www.ykmzc.com了解更多內容。

　　Above are 11 points for attention of torsion shear wrench. Summarize dry goods and make suggestions. Visit the website http://www.ykmzc.com for more information.